The Adesto® AT45DB321E is a 2.3V minimum, serial-interface sequential access Flash memory ideally suited for a wide variety of digital voice, image, program code, and data storage applications. The AT45DB321E also supports the RapidS serial interface for applications requiring very high speed operation. Its 34,603,008 bits of memory are organized as 8,192 pages of 512 bytes or 528 bytes each. In addition to the main memory, the AT45DB321E also contains two SRAM buffers of 512/528 bytes each. The buffers allow receiving of data while a page in the main memory is being reprogrammed. Interleaving between both buffers can dramatically increase a system’s ability to write a continuous data stream. In addition, the SRAM buffers can be used as additional system scratch pad memory, and E2PROM emulation (bit or byte alterability) can be easily handled with a self-contained three step read-modify-write operation.

The ENC28J60 is a stand-alone Ethernet controller with an industry standard Serial Peripheral Interface (SPI). It is designed to serve as an Ethernet network interface for any controller equipped with SPI. The ENC28J60 meets all of the IEEE 802.3 specifications. It incorporates a number of packet filtering schemes to limit incoming packets. It also provides an internal DMA module for fast data throughput and hardware assisted checksum calculation, which is used in various network protocols. Communication with the host controller is implemented via an interrupt pin and the SPI, with clock rates of up to 20 MHz. Two dedicated pins are used for LED link and network activity indication.

High Power LED Series 3535 Ceramic Hot Binning LH351C High efficacy and high quality color rendering makes the LH351C suitable use in a broad range of applications.

Features & Benefits:

– Operates at a maximum current of up to 2 A

– Uniform light distribution under any beam angle

– 90 CRI makes it well suited for most applications

– Hot binning @ 85 ºC Applications

– Indoor Lighting: Spotlight, Downlight

– Outdoor Lighting: Street Light, Tunnel Light, Security Light, Area Light, Stadium/Arena Light

– Industrial Lighting: High Bay Light, Low Bay Light

– Consumer Lighting: Torch Light.

The LM117 and LM317-N series of adjustable 3-pin • Typ. 0.1% Load Regulation positive voltage regulators are capable of supplying in • Typ. 0.01%/V Line Regulation excess of 1.5 A over a 1.25-V to 37-V output range • 1.5-A Output Current and a wide temperature range. They are • Adjustable Output Down to 1.25 V exceptionally easy to use and require only two external resistors to set the output voltage. Further, • Current Limit Constant With Temperature both line and load regulation are better than standard • 80-dB Ripple Rejection fixed regulators. • Short-Circuit Protected Output The LM117 and LM317-N offer full overload • −55°C to 150°C Operating Temperature Range protection such as current limit, thermal overload (LM117) protection and safe area protection. All overload protection circuitry remains fully functional even if the 2 Applications adjustment terminal is disconnected. • Automotive LED Lighting Typically, no capacitors are needed unless the device is situated more than 6 inches from the input filter • Battery Chargers capacitors, in which case an input bypass is needed. • Post Regulation for Switching Supplies An optional output capacitor can be added to improve • Constant Current Regulators transient response. The adjustment terminal can be • Microprocessor Supplies bypassed to achieve very high ripple rejection ratios that are difficult to achieve with standard 3-terminal Typical Application regulators.

This device is an 8-bit non-inverting level translator that uses two separate configurable power-supply rails. The A port tracks the VCCA pin supply voltage. The VCCA pin accepts any supply voltage between 1.4 V and 3.6 V. The B port tracks the VCCB pin supply voltage. The VCCB pin accepts any supply voltage between 1.65 V and 5.5 V. Two input supply pins allows for low Voltage bidirectional translation between any of the 1.5 V, 1.8 V, 2.5 V, 3.3 V, and 5 V voltage nodes

Kintex®-7 FPGAs are available in -3, -2, -1, -1L, and -2L speed grades, with -3 having the highest performance. The -2L devices are screened for lower maximum static power and can operate at lower core voltages for lower dynamic power than the -2 devices. The -2L industrial (I) temperature devices operate only at VCCINT = 0.95V. The -2L extended (E) temperature devices can operate at either VCCINT = 0.9V or 1.0V. The -2LE devices when operated at VCCINT = 1.0V, and the -2LI devices when operated at VCCINT = 0.95V, have the same speed specifications as the -2 speed grade, except where noted. When the -2LE devices are operated at VCCINT = 0.9V, the speed specifications, static power, and dynamic power are reduced. The -1L military (M) temperature devices have the same speed specifications as the -1 military temperature devices and are screened for lower maximum static power. Kintex-7 FPGA DC and AC characteristics are specified in commercial, extended, industrial, expanded (-1Q), and military (-1M) temperature ranges. Except for the operating temperature range or unless otherwise noted, all the DC and AC electrical parameters are the same for a particular speed grade (that is, the timing characteristics of a -1 speed grade military temperature device are the same as for a -1 speed grade commercial temperature device). However, only selected speed grades and/or devices are available in each temperature range. For example, -1M is only available in the defense-grade Kintex-7Q family, and -1Q is only available in XA Kintex-7 FPGAs. All supply voltage and junction temperature specifications are representative of worst-case conditions. The parameters included are common to popular designs and typical applications.